Swift Home Improvement
Product Specifications |
Look Up on Your Roof
Start Your Home Improvement Now Because...
"Love at first sight"
Begins with the "Curb Appeal" of your home |
For More Information About Specs Please Contact Ron or call 330-671-1968 |
|
|
Complete Swift Flue Wrap Includes
Support Structure: Aluminum* 36in. Inside Preformed Corners 4 Each
Support Structure (Extensions): Aluminum 36in. Inside Preformed Corners 4 Each
Box Lid: Tig-Welded Aluminum 23 3/16in. - With 3in. Pilot Hole 1 Each
Rear Flange: Aluminum 20in. - With 3 Pre-drilled Anchor Holes 1 Each
Brick Exterior: Marble Aggregate Bonded Over Durable 1in. Insul-Panel 4 Each
Mounting Hardware:
Knurled Inserts 1in. Plastic 25 Each
Machine Screws Zinc Plated 1/4 in. 30 Each
Lag Bolts Zinc Plated 1 1/2 in. Lag Bolts 5 Each
Washers Zinc Plated Flat Washers 5 Each
Mastic Adhesive:
All Weather Exterior Bonding Cement - 2 Tubes - 10 oz. ea.
Base Unit Interior Specifications: 21in. Square 3ft. Deep @ Front Panel
Extension Unit Interior Specifications: 21in. Square 3ft. Deep (Extensions Stack in 3ft. Increments)
Shipping Box: 37in. X 25in. X 7in.
Shipping Weight: 35Lbs. Aprx. (boxes)
Shipping Transportation: UPS
* .023 3003 H14 Aluminum
|
| Decorative Brick Chimney
1. DIY Swift - Pre Fabricated Brick Chimney
Standard:
2. Base Unit 2x 2x 3ft.
3. All Brick Colors - Same Price
4. Also Paintable Stucco
5. No Rust - Ever!
6. Earth Quake Proof
7. Only 35lbs. - 3ft. x 2ft.box - UPS Shipping (wgt. aprx.)
8. 3-5 Days Factory to You
Box includes all No Rust Material
- 4 brick panels pre-cut & matched for you
- 4 aluminum pre-formed legs (support structure)
- Lid welded aluminum with 3in. starter-hole
- Front Flange built into your aluminum pre-formed supports
- Rear Flange aluminum pre-formed
- Glue - 2 tubes
- Anchors, screws, washers, lags (all no-rust mounting hardware)
- Simple assembly & mounting instructions
Optional Contractor Kits
Custom Sizes & Colors Made to Order and are Special Order Only!
Matching Color Lids - $10.00
Flashing Kit - $30
White and Stone Brick
|
|
|
INSTALL A SWIFT FLUE WRAP IN JUST MINUTES!
Start here with "Variable Pitch" Model
Safely...On the ground:
1) Establish roof pitch of Home
2) Prepare to cut......Lay unit on its side.
3) Using furnished drawing determine angle / pitch to be cut.
(Example 3/12 pitch = 5 Ό in. up from bottom back corner of Flue Wrap)
4) Draw line from bottom front corner to desired roof pitch. (example 5 1/4"up=3/12pitch) mark and cut with circular saw. (carbide saw blade, recommended)
5) Repeat step #4 on opposite side.
6) After both sides (angles) are cut, draw a straight line connecting each side, now cut back side. (caution: do not cut front 36" side) Roof pitch cut is now complete.
7) Attach flange bracket to inside / back of flue wrap.
On the roof:
8) Remove spark arrester and storm collar from flue pipe.
9) Using 3" pilot hole. Cut lid to custom fit your flue pipe size.
10) Using Flue Wrap lid... Center flue wrap over / around flue pipe, mark location then remove lid.
11) Attach Flue Wrap to roof using galvanized lag screws, provided.
(Be sure to apply Adequate silicone under flange and around screw holes)
12) Apply an even bead of sealant across rear & sides "on the bottom" of flue wrap.
(You may leave front open for air flow and water drainage "ONLY" if flue is water tight)
13) Place lid over flue pipe and position securely on unit. (silicone use optional)
14) Replace spark arrester and storm collar on flue pipe.
"E x t e n s I o n" Installation Instructions
Remove spark arrester, storm collar and lid of Flue Wrap. Apply Ό in. bead of silicone to top surface & aluminum vertical inserts of extension. Being careful to align "half brick design" carefully place extension into top of Flue Wrap and press firmly. Replace lid, storm collar and spark arrester.
Helpful hint: Remember roof pitches may very, due to the construction and assembly of your home. |
|
